New Modular Inverters ECI Series – Efficient Power Conversion Technology

ECI Combines Three High-Efficiency Energy Converters And An Energy Buffer In A Single Module To Provide Polyvalent Power Conversion For Critical Systems At Up To 96% (AC/AC) And 94% (DC/AC & AC/DC) Efficiency. AC Source Wide AC input 150 to 265 Vac Active power factor correction Full bidirectional converter 0 mS transfer time to DC in case of AC input failure DC 94% DC/AC efficiency with double isolation DC batteries VRLA, NiCd, Liion Ultracap Fuel cells Optional MPPT ( Maximum Power Point Tracking) for direct connection to solar panel AC LOAD Pure sine output Stabilized +/- 1% 0 leading to 0% lagging 2kW / 2,5 kVA Communication Redundant com bus 32 modules in parallel on the same bus BOOST Short circuit peak 10xIn for 20 mS on ACin 3xIn on DC/AC for 20 mS Bravo 25 Modular Inverters: 48Vdc/230Vac 3kVA Read more Bravo 10 Modular Inverters 48Vdc/230Vac 1.25kVA-40kVA Read more Bravo 25 Modular Inverters: 380Vdc/230Vac 3kVA Read more For Any Power Conversion Scenario, You Might Be Thinking Of… MULTIPLE CONVERSION POSSIBILITIES The ECI technology allows for the set-up of each conversion stage to work in one or two directions depending on the final usage of the product in which it will be integrated: ACin, DCin and ACout only for inverter type applications ACin, DCin/out and ACout for UPS type applications ACin/out, DCin/out and ACin/out for multi conversion platform applications 94% ISOLATED DC/AC CONVERSION the most efficient DC/AC conversion on the market! DC to AC <=> 94% AC to AC <=> 96% Power-ECI-Sellsheet ECI Comes With Greater Efficiency, Reduced Footprint And Incredible Modularity While Retaining All The Benefits Of TSI.

Remote Monitoring – RMS Series

Remote Monitoring – RMS Series No matter how far o remote your site’s location maybe, as long as there is internet connectivity you will be able to Monitor your battery voltage over the internet with isolated voltmeters. Control generators, pumps, lights, turn devices on or off. Measurement of battery voltage and charging. Amperage measurement through a shunt. Measurement of wind turbine and solar panel output. Detection of A/C power, presence or absence. Door and window contact monitoring. Fuel tank level monitoring. Email and SMS Alerts. High reliability is extremely important for any remote communications site. Some remote sites are helicopter access only for most of the year. At $2000.00 per hour for a helicopter, you will want to plan your trips instead of reacting to dead batteries! RMS-100 Description Applications Features Relays Voltmeters Downloads Request a Quote Description RMS-100, the baby RMS; Is a unique remote monitoring, data acquisition, and control device specifically designed for use with Battery powered wireless internet repeater sites, or other AC & DC powered remote equipment RMS-100 Has ultra-low power consumption and won’t put a drain on your power source. Uses only 1.2 watts! RMS-100 Is powered by DC voltage from 10 to 60 volts. RMS-100 Uses embedded Ethernet technology for internet data acquisition and remote voltage monitoring. RMS-100 Uses the LINUX operating system for versatility, stability, and security. RMS-100 Gives you the situational awareness you need to keep your equipment operational and reliable. Applications Use RMS-100 to monitor battery levels, room temperature, signal strength (RSSI) on radios and more. RMS-100 has 3 onboard isolated voltmeters giving it the ability to measure DC voltage from -100 to +100 volts with 24 bit accuracy.RMS-100 also has 2 power relays giving it the unique ability to turn on/off devices remotely using an Internet connection. Use the power relays to remote start a generator. RMS-100 has 5 dedicated input pins used for door alarms, motion sensors, or to monitor solar panel trip wires. RMS-100 has two USB 2.0 ports that support several USB devices concurrently using a USB hub. Control USB cameras, store data on USB flash drives, control USB speakers etc. RMS-100 has input and output pins used to control your own custom devices. RMS-100 has ping monitor software that allows you to monitor network devices and alert you to failure and possibly power cycle the device. Monitor all this information remotely over an Internet connection using an ordinary web browser. RMS-100 gives you direct hardware control of fans, lights, computers, cameras, modems, radios, etc… No more guessing what your battery levels are. No more wondering if your signal strengths are at an acceptable level. No more long drives to reset a fussy radio. Let RMS-100 do this all remotely via the Internet. Features Six layer PCB with Nickel Immersion Gold plating and red solder mask. 400 – MHz Arm Processor (500 Mips !). 256 – megs of Nand Flash. Create and store custom applications. 64 megs of SD-Ram.  Dual Low Noise Switching Power Supplies accepts 8 – 60 vdc input. Can be powered directly from 12, 24, or 48 volt battery banks. Battery backed-up, real-time clock.· One onboard temperature sensor –25c +100c. Three 24 bit isolated voltmeters (+/- 100 VDC). Each voltmeter has its own 24 bit Delta Sigma ADC. Each voltmeter can be put into low voltage shunt mode (+/- 2 VDC). Two Power Relays for devices using 1 – 240v -5 amps AC/DC current. One programmable push button.  Four general purpose I/O pins. Five dedicated alarm pins.  One console serial port.  Two USB 2.0 ports for cameras, wireless clients, extra Ethernet, etc. Runs real Linux! 2.6.33 kernel. Send SMS messages, Email alerts, SNMP traps, Remote Syslog Messages. Ping watchdog, power cycle equipment after a set amount of ping timeouts. Command line utilities: ping, ftp, email, relays, etc. Flash new firmware over the internet. Duel Watchdog Reset circuits, processor integrated, and extra hardware. Control RMS-100 via web page, telnet, ssh, or snmp. Full SNMP v1, v2, v3 support (default v3). Supports external USB relays and voltmeters. Hardware is user accessible from files on the board. Make your own utilities and scripts to upload. (Bash, PHP, Python, Lua) Pluggable connectors for ease of use. Relays RMS-100 Has Two Power Relays Remote Control Of AC/DC Powered Equipment RMS-100 has two power relays for remote control of AC/DC powered equipment. Each relay has a manual override button that can toggle the relay; useful for on-site testing. Each relay also has a jumper shunt connector that allows the relay to be engaged manually for hands-free testing. Control of each relay can be done with a web browser. The picture below shows a portion of the RMS-100 relays web interface. In the picture below all relays are in the default “Normally Closed” position. By clicking on the relay 1 icon…. The relay will be toggled to the “Normally Open” position as shown below. Voltmeters RMS-100 has three 24 bit isolated voltmeters for sampling DC voltages up to 100 volts! Each voltmeter is capable of measuring up to +/- 100 VDC with 24-bit accuracy. Each voltmeter has its own 24 bit Delta Sigma ADC. The data and power lines for each voltmeter are isolated with a chip-scale air core transformer. This enables each voltmeter to measure different DC voltage sources without any effect on the main board or other voltages.This technology enables the ability to measure (but not limited to): Positive and negative voltages Separate power sources Individual batteries in a battery bank Shunt voltages for equipment that may be drawing or generating power. Solar panel voltage and amperage Wind turbine voltage and amperage Battery charger voltage and amperage Each voltmeter has a Mode Jumper that when removed puts the voltmeter into low voltage mode. In this mode, the volmeter has a range of +/- 2.0 VDC and has over 4 million steps. This is perfect for calculating amperage by measuring voltage drop across a current shunt. Downloads RMS-100 DATASHEET Request a Quote REQUEST A QUOTE RMS-300 Description Applications Features

Enertec joins forces with Helios Power Solutions

We are delighted to announce that as of 1 November 2016, Enertec Power Solutions Ltd will become part of Helios Power Solutions Ltd (formerly Innovative Energies Ltd) in Auckland. With the addition of the Enertec product range and their highly qualified staff, Helios will be able to provide an unmatched range of industrial power solutions to the NZ market. All of the current Enertec staff will be joining the new entity; customers and suppliers can expect the same high level of service and to deal with the same people they do at present. Both companies have been in existence for around 30 years, focusing on technical strength, high service and quality levels and innovative solutions to industrial power requirements. New products include the Riello range of AC UPS from Italy, Ablerex AC UPS and battery monitoring systems, Erico lightning and surge protection equipment and a range of other industrial power products. All of these are backed up by qualified service personnel and the ability to commit to long term service agreements. These products and services are complementary to the current Helios offer and the combined technical depth of the business is unmatched in NZ. In addition, we will now be able to provide improved service levels to the whole country, with increased technical sales resources in Auckland and people on the ground in Wellington and Christchurch. Helios Power Solutions is 100% NZ owned and includes the NZ business and operations in Sydney and Singapore. Taspac Energy is an associated company based in Henderson that focuses on distribution of leading products for the solar industry.