| MAIN OUTPUT SPECIFICATIONS | | |
Output power (continuous)
(5 s transient) | 85-132/170-264 Vrms
85-132/170-264 Vrms
132-170 Vrms | 1400 W
1800 W |
Nominal DC output
voltage (at 800W)
(Semi-regulated) | 12 Vout
15 Vout
24 Vout
28 Vout
48 Vout | 12.4 V
15.6 V
25 V
29 V
50 V |
| Efficiency | 12 Vout, 115 Vrms, 1400 W
24 Vout, 115 Vrms, 1400 W
48 Vout, 115 Vrms, 1400 W
12 Vout, 230 Vrms, 1400 W
24 Vout, 230 Vrms, 1400 W
48 Vout, 230 Vrms, 1400 W | 87% typ.
89% typ.
90% typ.
89.5% typ.
90.5% typ.
91.5% typ. |
| Hold-up time (to -20%) | 12 / 15 Vout
24 / 28 / 48 Vout | 10 ms @ 1400 W
12 ms @ 1400 W |
| Maximum load capacitance | 12 Vout
15 Vout
24 Vout
28 Vout
48 Vout | 48,000 μF
40,500 μF
24,000 μF
19,200 μF
6,000 μF |
| Output ripple voltage | Switching frequency (20 MHz BW)
Twice line frequency (at 800W) | 0.5% p-p
5.0% p-p |
| Turn-on delay | | 2 s max. |
| Transient response | Iout steps from 50-75%
At 0.2 A/μs | 3% typ / 6% max. dev.
100 ms recovery |
| Overvoltage protection | Cyclic restart | 110-120% |
| Short circuit protection | Cyclic operation | 115% rated Iout |
| Total regulation | Over line, load and temperature | ±6.0% |
| Auxillary Output | Always on (See Note 1) | 5 V @ 100 mA |
| Thermal protection | Automatic recovery | +125 ºC (PCB Temp) |
| REMOTE_ENABLE | Input Low Voltage
Input High Voltage | 0.45 V (max)
4.15 V (min) |
| INPUT SPECIFICATIONS | | |
| AC input voltage | Universal range | AC input voltage Universal range 85-264 Vrms |
| Input frequency | | Input frequency 47-63 Hz |
| Input current | 115 Vrms @ 1400 W
230 Vrms @ 1400 W | 14 Arms
7 Arms |
| Power factor | | >0.98 |
| Input surge | 264 Vrms (cold start) | 50 A max. |
| Internal input fuses | Both AC lines | 20 A |
| GENERAL SPECIFICATIONS | | |
| Fundamental ripple freq. | Fundamental ripple freq. Input 500 kHz | Fundamental ripple freq. Input 500 kHz |
| Output 250 kHz | Output 250 kHz |
Audible noise
Weight
( AQ0800xxxxGC )
( AQ1100xxxxGC )
( AQ1400xxxxGC ) | Fan speed varies with temp. | 45 dBA @ 1 m max.
998 g (35.2 oz)
1179 g (41.6 oz)
1179 g (41.6 oz) |
| MTBF | MIL-217
Demonstrated | 533 kHours
TBD kHours |
| ISOLATION SPECIFICATIONS | | |
| Isolation voltage | Input to output
Input to ground
Output to ground (BF & CF)
Output to ground (CFD) | 4000 Vrms
1500 Vrms
1500 Vrms
5000 Vpulse |
| Insulation resistance | Output to ground | 10 MΩ min. |
| ENVIRONMENTAL CHARACTERISTICS | |
| Thermal performance | Operating ambient (see Figure 11)
Non-operating ambient | 0 ºC to +70 ºC
-40 ºC to +85 ºC |
| Relative humidity | Non-condensing | 5-95% RH |
| Altitude | Operating
Non-operating | 10,000 ft max.
30,000 ft max. |
| Random vibration | 5-500 Hz | 0.03 g2/Hz |
| Shock | Half-sine, 10 ms, 3 axes | 20 g peak |
| EMC CHARACTERISTICS | | |
| Conducted emissions | EN55011 and EN55022, FCC part15 | Level B |
| Line frequency harmonics | EN61000-3-2 | Class A |
| Voltage fluctuations | EN61000-3-3 | Clause 5b |
ESD air
See following details | EN61000-4-2 | Level 4, +/-15kV
Perf Criteria A, AC Input Connections
Perf Criteria B, DC Output Connections |
| ESD contact | EN61000-4-2 | Level 4, +/-8kV
Perf Criteria A; HCP, VCP, Case |
| Radiated immunity | EN61000-4-3 | Level 3, 10V/m
IEC60601-1-2 Ed.4 Table 4
28 V/m
IEC60601-1-2 Ed.4 Table 9
Perf Criteria A |
| Fast transients | EN61000-4-4 | Level 3,
100KHz rep, AC input leads
IEC60601-1-2 Ed.4 Table 5
Perf Criteria A |
| Line surge immunity | EN61000-4-5 | Level 3
Perf Criteria B |
| Perf Criteria B | Perf Criteria B |
| Conducted immunity | EN61000-4-6 | Level 3
Perf Criteria A |
| Power freq. mag. Field | EN61000-4-8 | 30 A/m
IEC60601-1-2 Ed.4 Table 4
Perf Criteria A |
Voltage dip immunity
See following details | EN61000-4-11 | 0% Ut;
0.5 cycle 45° increments
0% Ut; 1 cycle
70% Ut; 0.5s
IEC60601-1-2 Ed.4 Table 5
Perf Criteria A, Load Dependent |
| Voltage interruptions | EN61000-4-11 | 0% Ut; 5s
IEC60601-1-2 Ed.4 Table 5
Perf Criteria B |
NOTES:
1. Derate 1 mA per °C above 50 °C ambient temperature.
2. Leakage currents see following table. | | |
